|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
PI3HDMI412-B 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Features * 3.3V VDD * 4-Differential Channel 2:1 Mux/DeMux * DVI, HDMI, 1.2 +1.2 signal compatible * Data Rate: 1.65Gbps * Supports both AC coupled and DC coupled signals * Crosstalk: -35dB@825MHz * Switching speed: 4ns * Isolation: -30dB@825MHz * Near-Zero Prop Delay: 250ps max. * Low bit-to-bit skew * Enable/Disable Time: 9ns * Bidirectional * Enhanced ESD Protection: - Switch pins: 1.1kV (machine model) 12kV (humanbody model) 8kV (contact)(1) * Packaging (Pb-free & Green): --48-pin TSSOP (A) Description Pericom Semiconductor's PI3HDMI series of switch circuits are targeted for high-resolution video networks that are based on DVI/ HDMI standards, and TMDS signal processing. The PI3HDMI412-B is a 8- to 4-Channel Mux/DeMux Switch. The device multiplexes differential signals to one of two corresponding outputs. The switch is bidirectional and offers little or no attenuation of the high-speed signals at the outputs. It is designed for low bit-to-bit skew and high channel-to-channel noise isolation. The maximum DVI/HDMI data rate of 1.65Gbps provides the resolution required by the next generation HDTV and PC graphics. Three differential channels are used for data (video signals for DVI or audio/video signals for HDMI), and one differential channel is used for Clock for decoding the TMDS signals at the outputs. Because of its passive bidirectional feature, this switch can be used either at the video drivers side or at the receiver side. For PC graphics applications, the device sits at the drivers side to switch between multiple display units such as PC LCD monitor, projector, TV, etc. For consumer video applications, the device sits at the receiver end to switch between the source components such as DVD, D-VHS, STB, etc. Block Diagram A0 A1 0B1 1B1 0B2 1B2 Pin Configuration V DD A0 GND A1 GND V DD GND A2 GND A3 GND V DD GND NC A4 GND A5 GND V DD GND A6 GND A7 SEL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 0B1 1B1 GND 0B2 1B2 A2 A3 2B1 3B1 2B2 3B2 GND 2B1 3B1 GND 2B2 3B2 A4 A5 4B1 5B1 4B2 5B2 GND V DD 4B1 5B1 A6 A7 6B1 7B1 6B2 7B2 GND 4B2 5B2 GND 6B1 7B1 SEL GND 6B2 7B2 Note: 1. IEC 61000-4-2 06-0050 1 PS8809B 04/26/06 PI3HDMI412-B 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Truth Table Function(1) Ax to xB1 Ax to xB2 SEL L H Note: 1 x=0 through 7 Pin Description Pin # 3,5,7,9,11,13,16, 18,20,22,27,30,3 3,37,40,43,46 1,6,12,19,36 14 2 4 8 10 15 17 21 23 24 25 26 28 29 31 32 34 35 38 39 41 42 44 45 47 48 Pin Name GND Type Power Description Ground VDD NC A0 A1 A2 A3 A4 A5 A6 A7 SEL 7B2 6B2 7B1 6B1 5B2 4B2 5B1 4B1 3B2 2B2 3B1 2B1 1B2 0B2 1B1 0B1 Power I/O I/O I/O I/O I/O I/O I/O I/O Input I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O Supply Voltage (3.3V 10%) No Connection TMDS Data 0TMDS Data 0+ TMDS Data 1TMDS Data 1+ TMDS Data 2TMDS Data 2+ TMDS Data 3TMDS Data 3+ Selection for Port 1 or Port 2 TMDS Data 3+ for Port 2 TMDS Data 3- for Port 2 TMDS Data 3+ for Port 1 TMDS Data 3- for Port 1 TMDS Data 2+ for Port 2 TMDS Data 2- for Port 2 TMDS Data 2+ for Port 1 TMDS Data 2- for Port 1 TMDS Data 1+ for Port 2 TMDS Data 1- for Port 2 TMDS Data 1+ for Port 1 TMDS Data 1- for Port 1 TMDS Data 0+ for Port 2 TMDS Data 0- for Port 2 TMDS Data 0+ for Port 1 TMDS Data 0- for Port 1 06-0050 2 PS8809B 04/26/06 PI3HDMI412-B 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Maximum Ratings (Above which useful life may be impaired. For user guidelines, not tested.) Storage Temperature....................................-65C to +150C Supply Voltage...................................................-0.5V to 3.6V DC Input Voltage ...............................................0V to VDD DC Output Current......................................................120mA Power Dissipation...........................................................0.5W Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC Electrical Characteristics for Switching over Operating Range (TA = -40C to +85C, VDD = 3.3V 10%) Paramenter VIH(3) VIL(3) VIK IIH IIL Description Input HIGH Voltage Input LOW Voltage Input HIGH Current Input LOW Current Test Conditions(1) Min. 0.65 (VDD) -0.5 -0.7 0.35 (VDD) -1.2 5 5 A V Typ.(2) Max. Units Guaranteed HIGH level Guaranteed LOW level VDD=Max., VIN=VDD VDD=Max., VIN=0V Clamp Diode Voltage VDD=Max., IIN=-18mA Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at TA = 25C ambient and maximum loading. 3. VIH + VIL are for SEL input only. 06-0050 3 PS8809B 04/26/06 PI3HDMI412-B 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Power Supply Characteristics Parameters ICC Description Quiescent Power Supply Current Test Conditions(1) VDD = Max., VIN = VDD or 0V Min. Typ.(2) 500 Max. Units A Dynamic Electrical Characteristics Over the Operating Range (TA= -40 to +85C, VDD = 3.3V 10%) Parameter XTALK Description Crosstalk Test Conditions See Fig. 1 for Measurement Setup, f = 825 MHz See Fig. 2 for Measurement Setup, f = 825 MHz Min. Typ.(2) -35 dB -30 1.65 Gbps Max. Units OIRR DR OFF Isolation Data Rate Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at TA = 25C ambient and maximum loading. Fig 1. Crosstalk Setup 06-0050 4 PS8809B 04/26/06 PI3HDMI412-B 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Fig 2. Off-isolation setup Fig 3. Crosstalk 06-0050 5 PS8809B 04/26/06 PI3HDMI412-B 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Fig 4. Off Isolation Switching Characteristics (TA= -40 to +85C, GND=0V, VDD=3.3V 10%) Paramenter tPZH, tPZL tPHZ, tPLZ Description(1) Min. 0.5 0.5 Typ. Max. 8.0 4.0 Units Line Enable Time - SEL to AN, BN Line Disable Time - SEL to AN, BN Notes: 1. For measurement setup, please see "Test Circuit For Electrical Characteristic" on page 6, and "Switching waveforms" on page 7 06-0050 6 PS8809B 04/26/06 PI3HDMI412-B 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Test Circuit for Electrical Characteristics Notes: * CL = Load capacitance: includes jig and probe capacitance. * RT = Termination resistance: should be equal to ZOUT of the Pulse Generator * Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. * All input impulses are supplied by generators having the following characteristics: PRR MHz, ZO = 50, tR 2.5ns, tF 2.5ns. * The outputs are measured one at a time with one transition per measurement. Switch Positions Test tPLZ, tPZL (output on B-side) tPHZ, tPZH (output on B-side) Prop Delay Switch 2 x (VDD) Gnd Open Test Circuit for Dynamic Electrical Characteristics 06-0050 7 PS8809B 04/26/06 PI3HDMI412-B 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard Switching Waveforms Voltage Waveforms Enable and Disable Times TP3 Rx Test Setup 06-0050 8 PS8809B 04/26/06 PI3HDMI412-B 4-Differential Channel, 2:1 Mux/DeMux, DVI/HDMI Compliant Signal Switch based on TMDS Signaling Standard TP3 eye diagrams with 3 meter cables With Switch With No Switch Packaging Mechanical: 48-pin TSSOP (A) 48 .236 .244 6.0 6.2 1 .488 12.4 .496 12.6 .047 1.20 Max SEATING PLANE .004 0.09 .008 0.20 X.XX X.XX DENOTES DIMENSIONS IN MILLIMETERS .0197 BSC 0.50 .007 .010 0.17 0.27 .002 .006 0.05 0.15 0.45 .018 0.75 .030 .319 BSC 8.1 Ordering Information Ordering Code PI3HDMI412-BAE Package Code A Package Description Pb-free & Green, 48-pin TSSOP Notes: * Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ * E = Pb-free and Green Pericom Semiconductor Corporation * 1-800-435-2336 * www.pericom.com 06-0050 9 PS8809B 04/26/06 |
Price & Availability of PI3HDMI412-BAE |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |